Any Raspberry Pi guys here? How can I go about Powering on/off a Pi 5 with this old TV PCB?

Any Raspberry Pi guys here?

How can I go about Powering on/off a Pi 5 with this old TV PCB?

250 Piece Survival Gear First Aid Kit

LifeStraw Water Filter for Hiking and Preparedness

250 Piece Survival Gear First Aid Kit

  1. 1 month ago
    Anonymous

    If you have the type of power supply that has a latching pushbutton you can remove that and replace it with one of the intermittent buttons on your TV board, plus something like a clothespin to keep the button pressed. To power down, you remove the clothespin.

    • 1 month ago
      Anonymous

      Amazing how a tech board pointed you to a boomer board that suggests using clothespins on a psu. Maybe use google anon and learn what a latch is.

      • 1 month ago
        Anonymous

        PrepHole Black folk can suck my dick, they should've pointed him to /SQTDDTOT/

        • 1 month ago
          Anonymous

          Leave it to the morons of PrepHole to not know their heads from their asses.

          Connect the PCB to the run pin on the PI and ground it. Done.

      • 1 month ago
        Anonymous

        Google doesnt showme jack fricking shit for this specific PCB you mouth breathing moron. frick off if you don't know.

        • 1 month ago
          Anonymous

          Ofc it doesnt, its a pcb of switches and a few diodes. You'll need some sort of latch circuit. I would say sorry for you being moronic but you are too entertaining.

          Leave it to the morons of PrepHole to not know their heads from their asses.

          Connect the PCB to the run pin on the PI and ground it. Done.

          Yes plz op make a short, post results.

          • 1 month ago
            Anonymous

            You're hopeless.

            Use the two pins from the power button, complete the circuit. There's no need to do anything else.

            • 1 month ago
              Anonymous

              That doesnt power off as per the OP. You're illiterate and likely a gorrila Black person.

              • 1 month ago
                Anonymous

                it powers off through software brainlet.

                There isn't any other way.

              • 1 month ago
                Anonymous

                Are you daft? Its a soft button for the bootloader. It initiates a shutdown in software if you detect it. Actual power stays live.
                You want actual power down you cut the rails. You want a software shutdown button fine but it wasnt the original OP.
                Also this is SQTDDTOT shit and EASILY GOOGLE ABLE as well as its commonly understood shit on /g.
                >there isnt another way
                Thats not what your mom said last nite.

              • 1 month ago
                Anonymous

                >your precious kbps of bandwidth

                OP is solved, dipshit. Just because you had to run to Google and return 30 minutes later with your mom jokes doesn't make me wrong.

              • 1 month ago
                Anonymous

                Its not a power off button its more of a reset. It doesnt actually power off, its just a pin the software looks at. You use this to invoke a proper os shutdown, then remove power after its complete.

                So yes you are very, very wrong.

              • 1 month ago
                Anonymous

                then what is the purpose of the power button entry in the device tree?

  2. 1 month ago
    Anonymous

    Is this a bot thread?

    • 1 month ago
      Anonymous

      Yes.

  3. 1 month ago
    Anonymous

    >How can I go about Powering on/off a Pi 5 with this old TV PCB?
    you... can't.

  4. 1 month ago
    Anonymous

    OP…can i pee in your butt

  5. 1 month ago
    Anonymous

    Does the PCB output 5V at 3.5A+?
    Is your solution going to be cheaper than a $7 psu from Amazon?

    Then frick off.

Your email address will not be published. Required fields are marked *