SO I WENT TO CHECK OUT MY CZ SCORPION 3+, BECAUSE I ENJOY LARPING WITH IT.
I GO TO CHECK TO ENSURE IT IS CHAMBERED, AS I KEEP ALL OF MY GUNS CHAMBERED AND LIKE TO VERIFY SUCH. I SEE BRASS, BUT NO BULLET.
NO.
FUCKING.
BULLET.
WHAT THE FUCK?
pic 1/3
pic 2/3
all the powder is gone
pic 3/3
What does your bore look like? Probably plugged with a projectile...
My guess is the bullet wasn't crimped properly in the case.
This. Had this happen with a 5.7. Defective ammo happens.
It happened to me once with Federal FMJ 5.7 stuff, it was like 5-6 years ago and occurred in my fiveseven handgun.
RETARD QUESTION: if you fired a gun that was full of loose powder, would it explode? it has to be under compression to explode, right?
it won't explode as far as I know unless there's some super specific scenario that I just can't think of. your gun might be on fire briefly though.
>if you fired a gun that was full of loose powder, would it explode?
no
It'd just go
>fwooosh
Or just fart it out the muzzle.
I had a series of squibs in my 45-70 and the powder didn't even light, just shat powder on the inside of my 1895 and gummed everything up.
You’re right you are a retard for that question. Gun powder is not explosive
It would just fizzle. When you burn powder it breaks down into a load of gas, you put this in a sealed container like a breach and barrel and the expanding gas pressure pushes the projectile out of the barrel
It doesn't necessarily even smoulder or anything. I had a squib in my AK, tapped it out, kept shooting for two range trips without cleaning in between and only afterwards noticed the receiver was full of loose gunpowder.
The front fell off? Is that normal?
It would just smoke a bit.
wha the absolute fuck has this board become
yer mudda
His point exactly
Nogunz brainlets who came for the youcrain tourism and had their toes sucked by jannies so they stayed
[USER WAS WARNED FOR THIS POST]
You should fire a good round behind it to push the bullet out.
And why do you have a semi-auto pistol caliber carbine? They are for gays.
>And why do you have a semi-auto pistol caliber carbine? They are for gays.
It was my 8th purchase bro, a fun gun to magdump stuff with
My next will be a Ruger Precision Rifle in .338 Lapua
Buy a 9mm blank, shoot it, and report back.
That's the built-in bullet puller accomplished by a novel trick of engineering where apparently your ammo has an excessive amount of jam. Is this factory ammo?
it is Federal 115gr FMJ training ammo
It's probably just the ammo, the combination of no crimp and a binding bullet seems like it's just an out-of-spec round. If you're still concerned, I'd have a gunsmith make sure the chamber was properly reamed. There should be a bit of jump between any factory ammo and the rifling.
it's fucking hilarious reading what not machinists have to say about these things. thanks for the laugh
It's even more hilarious seeing what not reloaders think about what other people have to say. Not that anon but OP's malfunction is obviously the product of a bullet that's not seated deep enough combined with insufficient crimp, or a barrel with insufficient jump between the lands and the chamber. I know because I've done this (sans powder) many times when finding the lands on a barrel.
Lol so much this, I'm not sure about their carbines but the CZ pistols definitely have a much shorter leade distance than other manufacturers (Not sure why, just the way they ream their chambers) and are very sensitive to bullet seating depth. Probably a cartridge with a too-long OAL but it's possible the leade could also be pretty short as well, compounding the problem.
Very low quality post. I'm not even going to bother asking for elaboration.
just tap rack and bang moron
I was going to laugh at the funny joke, but like, shoot a standard pressure 90gr through it and it'll probably blow it out with little issue. Maybe pull the bullet and tap out 1/4 of the powder to be safe, but it would "only" be like shooting a 200gr +p+.
Had this happen with a Fiocchi V-max .223 in my AR. Pain in the ass the get all the powder out.
Fire a blank through it
>op making a thread for what is obviously ghosts stealing his bullets
like come on man, isn't it obvious?
Its like a bullpup muzzle loader.
You load it from the chamber, first the projectile, jam it in tight. Then you poor the powder in. Then you put the casing in and close the bolt, pressing it all together, now it's ready to fire.
The bullet is definitely supposed to leave the gun, OP. That is functioning as intended.
Congrats on the world's slowest ND!
Omg. Evo3 is such a whore, she literally sucked the bullet out of the case inside the barrel. You should shoot her more ofter and harder...
Running Norma by chance?